ENGINE PERFORMANCE

Replace stock plastic cap with Aluminum Cap includes sure seal rubber o-ring.  Sold separately.  May or may not be anodized at time of purchase.

 Replace stock plastic cap with Aluminum Cap includes sure seal rubber o-ring.  Sold separately.  May or may not be anodized at time of purchase. 

Replace stock fill plug with Aluminum Animal fuel pump breather to draw vacuum from crank case to fuel pump for optimal engine operation.

Replace pull rope with starter nut, uses 3/4" socket 5hp for Briggs and Animal or 5/16" Hex Key.  Plated to prevent rusting.

 Replace pull rope with starter nut, uses 3/4" socket 5hp for Briggs and Animal or 5/16" Hex Key.  Plated to prevent rusting. 

 Replace pull rope with starter nut, uses 3/4" socket 5hp for Briggs and Animal or 5/16" Hex Key.  Plated to prevent rusting. 

Eliminate oil blow with Aluminum Cat Can with petcock to drain excess oil.  2" O.D. x 5" Body with removable ends and reusable breather cap.  Mounts to rear or side bumper with (KKP-2108) aluminum bracket.  Available colors:  (BL) Blue, (BK) Black &

 (R) Red

Bracket clamps onto (KKP-2106) Catch Can with 3/4" seat strut.  Can also be used for mounting brackets on (KKP-1120) Lead Weight Canister.

Easily adjust air to fuel ratio day or night with knobs instead of T-bars for easier and more precise adjustments.

• Daytime:  See the color coded knobs with different lengths.
• Nightime:  Feel the different lengths and the thumb notch.

Keep dirt out of your crank case by filling the empty hole in the valve cover of Briggs Animal engines and run to catch can.

Excellent in keeping heat in your motor.  Once Piece Lexan guard allows you to see your timing marks.

This kit comes with high tensile studs and heat treated 12 point nuts to keep your headers tight and not leak.  Special 12 point drive is easy hex key engagement.

 This kit comes with high tensile studs and heat treated 12 point nuts to keep your headers tight and not leak.  Special 12 point drive is easy hex key engagement. 

 Find top dead center valve travel and lift for cams or check crank shaft play.  Indicator has 1" full travel with bracket. 

 Eliminate oil blow with Aluminum Cat Can with petcock to drain excess oil.  2" O.D. x 9-1/8"" Body with removable ends and reusable breather cap for easy cleaning.  Available colors:  (BL) Blue, (BK) Black & (R) Red  

Toe Lock is perfect for locking steering shaft and front end of kart.  Nylon bearing included.  Works well with (KKP-5100) Laser Toe Gauge Chassis alignment tool.

Easily adjust your steering wheel position.  2 position steering block will give 2-3/4" adjustment up or down.

 Easily adjust your steering wheel position.  3 position steering block will give 3-3/4" adjustment up or down. 

Aluminum cap with o-ring fits most common Go Kart brake cylinders.  

Available colors:  (BL) Blue, (R) Red

Measures .925 O.D. x .625 I.D. x .125 Long.

Zinc plated front wheel spacers.  

 (2 per pack)

Measures .925 O.D. x .625 I.D. x .250 Long.

Zinc plated front wheel spacers.

(2 per pack)

 Measures .925 O.D. x .625 I.D. x .500 Long.  Zinc plated front wheel spacers.

(2 per pack) 

Quickly add or move weight with this lead weight canister.  Short 5" holds up to 4 lbs. of lead shot.  Mount with (KKP-2108) Aluminum bracket anywhere on kart.

Available colors:  (BK) Black, (BL) Blue & 

(R) Red

 Quickly add or move weight with this lead weight canister.  Short 9-1/8" holds up to 7 lbs. of lead shot.  Mount with (KKP-2108) Aluminum bracket anywhere on kart.  Available colors:  (BK) Black, (BL) Blue & 

(R) Red 

Smooth flange nuts.  Set of 12.

Smooth flange nuts.  Set of 100.

Karting studs are easy to start nuts.  Similar to NASCAR wheel studs produced by KRC.  Set of 12.

Set includes:  Quick Start Wheel Studs, 12 quantity & Smooth Flange Nuts, 12 quantity.

Easily and accurately square your chassis and align your front toe.  Place the laser on the right read hub to square the kart with the laser, then measure to the front with marked plates on the front hubs.

 Easily and accurately square your chassis and align your front toe.  Place the laser on the right read hub to square the kart with the laser, then measure to the front with marked plates on the front hubs. 

This handy sprocket alignment laser will  make it easy to line up your sprocket & clutch.  This work well with 35 chain sprockets.

 This handy sprocket alignment laser will  make it easy to line up your sprocket & clutch.  This work well with 219 chain sprockets. 

 This handy sprocket alignment laser will  make it easy to line up your sprocket & clutch.  This work well with 520 chain sprockets.